7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers

Last Updated on November 2, 2018 by Admin

7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers

Lab – Configure a NIC to Use DHCP in Windows (Answers Version)

Introduction

In this lab, you will configure an Ethernet NIC to use DHCP to obtain an IP address and test connectivity between two computers.

Recommended Equipment

  • Wireless router
  • Two computers running Windows
  • Ethernet patch cables (straight-through cable)

Answers Note: Complete the NIC configuration before class to make sure that the NIC acquires an IP address.

Step 1: Connect the hosts to the router.

  1. For Host A, plug one end of the Ethernet patch cable into Port 1 of the router.
  2. For Host A, plug the other end of the Ethernet patch cable into the network port on the computer.
  3. For Host B, plug one end of the Ethernet patch cable into Port 2 on the back of the router.
  4. For Host B, plug the other end of the Ethernet patch cable into the network port on the computer.
  5. Plug in the power cable of the router, if it is not already plugged in.
  6. Turn on both computers and log on to Windows on Host A as an administrator.
  7. Click Control Panel > Network and Sharing Center. The Network and Sharing Center window opens.

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 01

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 01

Step 2: Set Host A’s NIC to use DHCP.

  1. Click Local Area Connection > Properties. The Local Area Connection Properties window opens.
    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 02

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 02

    What is the name and model number of the NIC in the Connect using: field?____________________________________________________________________________________
    Answers may vary.
    What are the items listed in the This connection uses the following items: field?
    ____________________________________________________________________________________
    Answers may vary but must include Internet Protocol Version 4 (TCP/IPv4).

  2. Click Internet Protocol Version 4 (TCP/IPv4) > Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties window opens.
    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 03

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 03

    What is listed for the IP address, Subnet mask, and Default gateway in the fields of the Use the following IP address: area?
    ____________________________________________________________________________________
    Answers may vary. If the computer is configured to obtain an IP address automatically, there will be no information in the fields.

  3. Select the Obtain an IP address automatically radio button, if it is not already selected.
  4. Select the Obtain DNS server address automatically radio button, if it is not already selected.
  5. Click OK to close the Internet Protocol Version 4 (TCP/IPv4) Properties window.

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 04

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 04

  6. Click OK to close the Local Area Connection Properties window.

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 05

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 05

  7. Click Close to close the Local Area Connection Status window.

Step 3: Record Host A’s IP address information.

  1. Check the lights on the back of the NIC. These lights will blink when there is network activity.
  2. Open a command window.
  3. Type ipconfig /all, and then press the Enter key.
    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 06

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 06

    What is the IP address of the computer? ________________________________________________
    Answers may vary.
    What is the subnet mask of the computer?_______________________________________________
    Answers may vary.
    What is the default gateway of the computer?____________________________________________
    Answers may vary.
    What are the DNS servers for the computer?______________________________________________
    Answers may vary.
    What is the MAC address of the computer?_______________________________________________
    Answers will vary.
    Is DHCP enabled?_________________________________________________________________________
    Yes
    What is the IP address of the DHCP server?_______________________________________________
    Answers will vary.
    On what date was the lease obtained?____________________________________________________
    Answers may vary.
    On what date does the lease expire?______________________________________________________
    Answers may vary.

  4. Type ping your IP address. For example, ping 192.168.1.112.

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 07

    7.4.1.11 Lab – Configure a NIC to Use DHCP in Windows Answers 07

  5. Record one of the replies from your ping command.
    ____________________________________________________________________________________
    Answers may vary.
    If the ping was not successful, ask the Answers for assistance.

Step 4: Record Host B’s IP address information.

  1. Log in to Host B as an administrator and ensure the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons are selected.
  2. Click OK > OK.
  3. Open a command window.
  4. Type ipconfig /all.
    What is the IP address of the computer? _________________________________________
    Answers may vary.
    What is the subnet mask of the computer?_________________________________________
    Answers may vary.
    What is the default gateway of the computer?_________________________________________
    Answers may vary.
    What are the DNS servers for the computer?_________________________________________
    Answers may vary.
    What is the IP address of the DHCP server?_________________________________________
    Answers will vary.

Step 5: Set static IP address information.

  1. Select the radio buttons Use the following IP address and Use the following DNS server address.
  2. Enter in the IP address information for the NIC from the previous step.
  3. Click OK > OK.
  4. Open a command window.
  5. Type ping IP address for Host B.
    If the ping was not successful, ask the Answers for assistance.

Step 6: Verify Connectivity.

  1. From Host B, type ping IP address for Host A.
    Was the ping successful?_________________________________________________
    Yes
  2. From Host A type ping IP address for Host B.
    Was the ping successful?_________________________________________________
    Yes
  3. Return all network configurations to their original settings, unless stated otherwise by the Answers.
  4. Set the NIC to Obtain an IP address automatically and Obtain DNS server address automatically.
  5. Click OK > OK.