Last Updated on October 29, 2019 by Admin
RSE CCNA 2 Chapter 5 Quiz Online
RSE -- Chapter 5 Quiz
Quiz-summary
0 of 15 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
Information
RSE — Chapter 5 Quiz
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 15 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
| Average score |
|
| Your score |
|
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- Answered
- Review
-
Question 1 of 15
1. Question
1 pointsWhat is a possible cause of runt Ethernet frames when a switch is being used?Correct
Incorrect
A runt frame is a frame that is smaller than 64 bytes, the minimum allowed Ethernet frame. This type of frame is usually due to a malfunctioning NIC or excessive collisions. Duplex misconfiguration can cause connectivity issues. Excessive cable length can generate CRC errors and/or late collisions.
Hint
A runt frame is a frame that is smaller than 64 bytes, the minimum allowed Ethernet frame. This type of frame is usually due to a malfunctioning NIC or excessive collisions. Duplex misconfiguration can cause connectivity issues. Excessive cable length can generate CRC errors and/or late collisions.
-
Question 2 of 15
2. Question
1 pointsWhat is the result of issuing the no switchport port-security mac-address sticky command on an interface with port security configured?Correct
Incorrect
Sticky learning is disabled by using the no switchport port-security mac-address sticky command. Any sticky secure MAC addresses remain as part of the mac-address table but are removed from the running configuration.
Hint
Sticky learning is disabled by using the no switchport port-security mac-address sticky command. Any sticky secure MAC addresses remain as part of the mac-address table but are removed from the running configuration.
-
Question 3 of 15
3. Question
1 pointsWhat would be the most common reason that a network technician would see the following Cisco switch prompt after the switch boots?
switch:
Correct
Incorrect
The prompt of “switch:” is seen when the switch cannot find an operating system and is in the boot loader environment where only a few basic commands can be used to repair the switch to an operational state. When an administrator has used Telnet or SSH to gain access to a switch prompt, the prompt usually asks for a username and password or is in user EXEC mode (switch>, for example).
Hint
The prompt of “switch:” is seen when the switch cannot find an operating system and is in the boot loader environment where only a few basic commands can be used to repair the switch to an operational state. When an administrator has used Telnet or SSH to gain access to a switch prompt, the prompt usually asks for a username and password or is in user EXEC mode (switch>, for example).
-
Question 4 of 15
4. Question
1 pointsA network administrator has configured VLAN 99 as the management VLAN and has configured it with an IP address and subnet mask. The administrator issues the show interface vlan 99 command and notices that the line protocol is down. Which action can change the state of the line protocol to up?Correct
Incorrect
Once an SVI is configured with an IP address and subnet mask, it can be used for remote management. An SVI interface will be active when the SVI VLAN has an active port associated with it.
Hint
Once an SVI is configured with an IP address and subnet mask, it can be used for remote management. An SVI interface will be active when the SVI VLAN has an active port associated with it.
-
Question 5 of 15
5. Question
1 pointsFill in the blank.
In an Ethernet network, frames smaller than 64 bytes are called ……………………… .Correct
Incorrect
Giants are Ethernet frames that are larger than the maximum allowed. Runts are Ethernet frames that are smaller than the minimum allowed.
Hint
Giants are Ethernet frames that are larger than the maximum allowed. Runts are Ethernet frames that are smaller than the minimum allowed.
-
Question 6 of 15
6. Question
1 pointsRefer to the exhibit. What can be determined from the partial output of the show running-config command?
RSE CCNA 2 Chapter 5 Quiz Answers 2018 2019 01
Correct
Incorrect
If the switch was unable to find and load the IOS, the prompt would be switch:. A Layer 2 switch does not provide the default gateway for connected hosts. The default gateway is provided by a Layer 3 device. The switch cannot be managed remotely until a management VLAN and a default gateway have been configured.
Hint
If the switch was unable to find and load the IOS, the prompt would be switch:. A Layer 2 switch does not provide the default gateway for connected hosts. The default gateway is provided by a Layer 3 device. The switch cannot be managed remotely until a management VLAN and a default gateway have been configured.
-
Question 7 of 15
7. Question
1 pointsHere is a link to the PT Activity.
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Fill in the blank.
Do not use abbreviations.What is the missing command on S1? …………………………..Correct
Incorrect
The ip address 192.168.99.2 255.255.255.0 command is missing on interface vlan 99, the management VLAN.
Hint
The ip address 192.168.99.2 255.255.255.0 command is missing on interface vlan 99, the management VLAN.
-
Question 8 of 15
8. Question
1 pointsFill in the blank.
The initialism ………………………. refers to a protocol that provides an encrypted connection. The protocol replaces the clear text Telnet protocol for Cisco device management.Correct
Incorrect
SSH is the initialism for Secure Shell, a secure protocol for remote access.
Hint
SSH is the initialism for Secure Shell, a secure protocol for remote access.
-
Question 9 of 15
9. Question
1 pointsWhat is the bandwidth utilization efficiency of full-duplex Ethernet?Correct
Incorrect
Full-duplex communication allows for an effective bandwidth efficiency of 100% by allowing both ends of a connection to transmit and receive data simultaneously without collisions. Ethernet frames that are sent by connected devices on a full-duplex Ethernet segment cannot collide because the devices use two separate circuits in the network cable, one circuit for receiving and one circuit for transmitting.
Hint
Full-duplex communication allows for an effective bandwidth efficiency of 100% by allowing both ends of a connection to transmit and receive data simultaneously without collisions. Ethernet frames that are sent by connected devices on a full-duplex Ethernet segment cannot collide because the devices use two separate circuits in the network cable, one circuit for receiving and one circuit for transmitting.
-
Question 10 of 15
10. Question
1 pointsWhich configuration must be in place for the auto-MDIX feature to function on a switch interface?Correct
Incorrect
The auto-MIDX feature only functions on Cisco devices when the speed and duplex of the connected interfaces are set to auto detect.
Hint
The auto-MIDX feature only functions on Cisco devices when the speed and duplex of the connected interfaces are set to auto detect.
-
Question 11 of 15
11. Question
1 pointsAn attacker has bypassed physical security and was able to connect a laptop to a Ethernet interface on a switch. If all the switch ports are configured with port security and the violation mode is set to factory-default, which action is taken against the attacker?Correct
Incorrect
The default violation mode is shutdown. In this mode, a port security violation causes the interface to immediately become error-disabled and turns off the port LED. It also sends an SNMP trap, logs a syslog message, and increments the violation counter.
Hint
The default violation mode is shutdown. In this mode, a port security violation causes the interface to immediately become error-disabled and turns off the port LED. It also sends an SNMP trap, logs a syslog message, and increments the violation counter.
-
Question 12 of 15
12. Question
1 pointsA network administrator plugs a new PC into a switch port. The LED for that port changes to solid green. What statement best describes the current status of the port?Correct
Incorrect
-
Question 13 of 15
13. Question
1 pointsA college offers classes at a nearby naval base where a remote switch is located. In order for network administrators at the college main office to manage a remote switch for SSH traffic, which destination port number should be opened and tracked on the college firewall?Correct
Incorrect
-
Question 14 of 15
14. Question
1 pointsRefer to the exhibit. The switch and workstation are administratively configured for full-duplex operation. Which statement accurately reflects the operation of this link?
RSE CCNA 2 Chapter 5 Quiz Answers 2018 2019 02
Correct
Incorrect
-
Question 15 of 15
15. Question
1 pointsWhat is the first action in the boot sequence when a switch is powered on?Correct
Incorrect
The first action to take place when a switch is powered on is the POST or power-on self-test. POST performs tests on the CPU, memory, and flash in preparation for loading the boot loader.
Hint
The first action to take place when a switch is powered on is the POST or power-on self-test. POST performs tests on the CPU, memory, and flash in preparation for loading the boot loader.