CCNA3 Final Exam (v5.03) 2016

CCNA3 Final Exam Answer v5.03 2016 A network designer is considering whether to implement a switch block on the company network. What is the primary advantage of deploying a switch block? A single core router provides all the routing between VLANs. The failure of a switch block will not impact all end users. This is […]
Continue reading…

 

CCNA3 Practice Final Exam (v5.03) 2016

CCNA3 Practice Final Exam Answer v5.03 2016 Which technological factor determines the impact of a failure domain? the number of layers of the hierarchical network the number of users on the access layer the role of the malfunctioning device the forwarding rate of the switches used on the access layer Which routing protocol is able […]
Continue reading…

 

CCNA3 Chapter 9 Exam (v5.03) 2016

CCNA3 Chapter 9 Exam Answer v5.03 2016 Which IOS 12.4 software package integrates full features, including voice, security, and VPN capabilities, for all routing protocols? Advanced Security Advanced IP Services Advanced Enterprise Services Service Provider Services What is the major release number in the IOS image name c1900-universalk9-mz.SPA.152-3.T.bin? 2 3 15 52 1900 What statement […]
Continue reading…

 

CCNA3 Chapter 8 Exam (v5.03) 2016

CCNA3 Chapter 8 Exam Answer v5.03 2016 Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be calculated on R3? (Choose two.) 192.168.1.0/30 192.168.10.0/30 192.168.10.0/24 172.16.3.0/24 172.16.0.0/16 Refer to the exhibit. Router R3 is receiving multiple routes […]
Continue reading…

 

CCNA3 Chapter 7 Exam (v5.03) 2016

CCNA3 Chapter 7 Exam Answer v5.03 2016 Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface? network 172.16.23.64 0.0.0.63 network 172.16.23.0 255.255.255.192 network 172.16.23.64 0.0.0.127 network 172.16.23.0 255.255.255.128 What is the purpose of using protocol-dependent modules in EIGRP? […]
Continue reading…

 

CCNA3 Chapter 6 Exam (v5.03) 2016

CCNA3 Chapter 6 Exam Answer v5.03 2016 Why do OSPF serial interfaces usually require manual bandwidth configuration? OSPF uses the bandwidth value to compute routes for its routing table. Each side of an OSPF serial link should be configured with a unique value. All serial interfaces default to a value of 1.544 Mb/s. Bandwidth value […]
Continue reading…

 

CCNA3 Chapter 5 Exam (v5.03) 2016

CCNA3 Chapter 5 Exam Answer v5.03 2016 Refer to the exhibit. What three conclusions can be drawn from the displayed output? (Choose three.) The DR can be reached through the GigabitEthernet 0/0 interface. This interface is using the default priority. The BDR has three neighbors. The router ID on the DR router is 3.3.3.3 The […]
Continue reading…

 

CCNA3 Chapter 4 Exam (v5.03) 2016

CCNA3 Chapter 4 Exam Answer v5.03 2016 Which IEEE wireless standard is known as WiGig and operates using a tri-band solution in the 2.4, 5, and 60 GHz ranges? 802.11g 802.11n 802.11ac 802.11ad Which two roles are typically performed by a wireless router that is used in a home or small business? (Choose two.) repeater […]
Continue reading…

 

CCNA3 Chapter 3 Exam (v5.03) 2016

CCNA3 Chapter 3 Exam Answer v5.03 2016 The trunk link between two 2960 switches has reached its capacity. How can this be addressed in the most economical way? Increase the speed of the ports. Decrease the size of the inter-switch collision domain by configuring additional VLANs. Combine physical ports into a high-speed logical link by […]
Continue reading…

 

CCNA3 Chapter 2 Exam (v5.03) 2016

CCNA3 Chapter 2 Exam Answer v5.03 2016 What could be the effect of duplicate unicast frames arriving at a destination device due to multiple active alternative physical paths? Frame collisions increase. The number of broadcast domains increases. Application protocols malfunction. The number of collision domains increases. What additional information is contained in the 12-bit extended […]
Continue reading…

 

CCNA3 Chapter 1 Exam (v5.03) 2016

CCNA3 Chapter 1 Exam Answer v5.03 2016 Which two features of enterprise class equipment assists an enterprise network in maintaining 99.999 percent up-time? (Choose two.) failover capabilities collapsed core redundant power supplies failure domains services module Refer to the exhibit. Which devices exist in the failure domain when switch S3 loses power? S4 and PC_2 […]
Continue reading…

 

CCNA3 Pretest Exam (v5.03) 2016

CCNA3 Pretest Exam Answer v5.03 2016 A router needs to be configured to route within OSPF area 0. Which two commands are required to accomplish this? (Choose two.) RouterA(config)# router ospf 0 RouterA(config)# router ospf 1 RouterA(config-router)# network 192.168.2.0 0.0.0.255 0 RouterA(config-router)# network 192.168.2.0 0.0.0.255 area 0 RouterA(config-router)# network 192.168.2.0 255.255.255.0 0 The computers used […]
Continue reading…