CCNA 3 v5.02 Routing and Switching 2015(100%)

CCNA 3 Practice Final Exam Which technological factor determines the impact of a failure domain? the number of layers of the hierarchical network the number of users on the access layer the role of the malfunctioning device the forwarding rate of the switches used on the access layer Which routing protocol is able to scale […]
Continue reading…

CCNA 3 Chapter 9 Which IOS 12.4 software package integrates full features, including voice, security, and VPN capabilities, for all routing protocols? Advanced Security Advanced IP Services Advanced Enterprise Services Service Provider Services What is the major release number in the IOS image name c1900-universalk9-mz.SPA.152-3.T.bin? 2 3 15 52 1900 What statement describes a Cisco […]
Continue reading…

CCNA 3 Chapter 8 Refer to the exhibit. All networks are active in the same EIGRP routing domain. When the auto-summary command is issued on R3, which two summary networks will be advertised to the neighbors? (Choose two.) 192.168.1.0/30 192.168.10.0/30 192.168.10.0/24 172.16.3.0/24 172.16.0.0/16 Refer to the exhibit. Router R3 is receiving multiple routes through the […]
Continue reading…

Which protocol is used by EIGRP to send hello packets? TCP UDP RTP IP When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used? bounded updates partial updates EIGRP authentication Diffusing Update Algorithm Reliable Transport Protocol What is the purpose of using protocol-dependent modules in EIGRP? to […]
Continue reading…

CCNA 3 Chapter 6 Which statement describes a multiarea OSPF network? It consists of multiple network areas that are daisy-chained together. It requires a three-layer hierarchical network design approach. It has a core backbone area with other areas connected to the backbone area. It has multiple routers that run multiple routing protocols simultaneously, and each […]
Continue reading…

CCNA 3 Chapter 5 A network administrator has just changed the router ID on a router that is working in an OSPFv2 environment. What should the administrator do to reset the adjacencies and use the new router ID? Configure the network statements. Change the interface priority. Issue the clear ip ospf process privileged mode command. […]
Continue reading…

CCNA 3 Chapter 4 Which organization certifies vendors for adherence to the 802.11 standards to improve interoperability of 802.11 products? FCC IEEE ITU-R Wi-Fi Alliance Which two roles are typically performed by a wireless router that is used in a home or small business? (Choose two.) repeater access point WLAN controller Ethernet switch RADIUS authentication […]
Continue reading…

CCNA 3 Chapter 3 Refer to the exhibit. Which switching technology would allow each access layer switch link to be aggregated to provide more bandwidth between each Layer 2 switch and the Layer 3 switch? HSRP PortFast trunking EtherChannel What is the most cost-effective method of solving interface congestion that is caused by a high […]
Continue reading…

CCNA 3 Chapter 2 Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.) static default routes implementing VLANs to contain broadcasts redundant links between Layer 2 switches link-state dynamic routing that provides redundant routes removing single points of failure with multiple Layer 2 switches What is a […]
Continue reading…

CCNA 3 Chapter 1 Which two features of enterprise class equipment assists an enterprise network in maintaining 99.999 percent up-time? (Choose two.) failover capabilities collapsed core redundant power supplies failure domains services module   Refer to the exhibit. Which devices exist in the failure domain when switch S3 loses power? S4 and PC_2 PC_3 and […]
Continue reading…

CCNA 3 Pretest Exam A router needs to be configured to route within OSPF area 0. Which two commands are required to accomplish this? (Choose two.)  RouterA(config)# router ospf 0 RouterA(config)# router ospf 1 RouterA(config-router)# network 192.168.2.0 0.0.0.255 0 RouterA(config-router)# network 192.168.2.0 0.0.0.255 area 0 RouterA(config-router)# network 192.168.2.0 255.255.255.0 0   The computers used by […]
Continue reading…

CCNA 1 Final Exam Which communication tool allows real-time collaboration? wiki e-mail weblog instant messaging A host is accessing a Web server on a remote network. Which three functions are performed by intermediary network devices during this conversation? (Choose three.) regenerating data signals acting as a client or a server providing a channel over which […]
Continue reading…

CCNA 3 Final Exam Which address is used by an IPv6 EIGRP router as the source for hello messages? the 32-bit router ID the IPv6 global unicast address that is configured on the interface the all-EIGRP-routers multicast address the interface IPv6 link-local address Which two statements are correct about EIGRP acknowledgment packets? (Choose two.) The […]
Continue reading…